Last Thursday I attended THE STANDARD Economic Forum 2026 in Bangkok, "Reinvent Thailand", and sat in on four sessions. The common thread I found throughout the discussions was focused on "whether the money coming into Thailand reaches Thai companies".

Nakarin Wanakijpaibul (Ken), CEO and Editor-in-Chief of THE STANDARD, asked it directly. In his interview with Narit Therdsteerasukdi, Secretary General of the Board of Investment (BOI), he asked, "when would the investment reach Thai supply chains and Thai small and medium enterprises (SMEs)".

Marc Spiegel with Nakarin Wanakijpaibul of THE STANDARD at THE STANDARD Economic Forum 2026 in Bangkok.

A few minutes later he raised the complaint you hear frequently from Thai citizens, that a lot of times foreign investors bring their own supply chains with them, so they don't see any direct benefit.

In electronics manufacturing, the bill of material (BOM) purchasing is where much of the money goes overseas. As a rule of thumb, up to 80% of direct material purchasing goes to non-Thai suppliers. The factories buy through international component distributors, and the stock will often be in Singapore or another overseas warehouse. There are even integrated circuits (ICs) assembled in Thailand, which then go overseas for testing or storage, and finally returned to a factory here for the next stage of production.

As a rule of thumb, up to 80% of direct material purchasing goes to non-Thai suppliers.

Thai companies typically supply packaging, tooling, stencils, fixtures and some mechanical parts. Packaging is only a small expense in the manufacturing process. Mechanical parts which require large quantities may still need to be purchased from China due to the Thai supplier cost being too expensive, limited capacity, or unavailability. Electronic components consume most of the material budget, but the number of Thai-owned manufacturers and distributors in that business segment is limited.

There are also restrictions in the case of contract manufacturing. The customer controls the BOM with already approved component makers, and in some cases a named distributor. A factory finding a suitable Thai part still needs customer approval prior to any changes. In joint-design manufacturing (JDM), the factory is involved in the product design too, which gives it more flexibility in choosing the BOM parts and where to buy them.

For Thai SMEs looking for new business opportunities, the parts EMS factories currently buy through large global distributors such as Arrow and Avnet are a good place to start. Some may be suitable for local manufacturing, or for a Thai company to stock and distribute at a more competitive price. Customer approval would still be required as part of the preparation. BOI can put SMEs in contact with manufacturers; however, after that, someone in purchasing and engineering at the manufacturer has to take responsibility for getting the Thai supplier approved.

Japanese carmakers spent years teaching Thai suppliers

AMRO has reported that some Japanese carmakers in Thailand now source more than 90% of their parts locally. The country has more than 2,300 domestic parts manufacturers. Thailand spent almost 30 years building its automotive manufacturing and supplier base. The 1990s was the golden moment for us to receive international recognition being called the "Detroit of Asia". It took approximately another ten years for Thailand to reach annual production of one million vehicles.

To bolster effort into other sectors, AMRO suggested making supplier development one of the conditions for large foreign investment projects. In February 2026, the World Bank went even further, proposing requirements for local sourcing, training and participation by SMEs. This sentiment was echoed by major manufacturers at this year's Economic Forum as well.

During a panel discussion on Southeast Asia, AI and regional integration, moderated by Ken, Gita Wirjawan, former Minister of Trade for Indonesia, called Thailand "the best success story in Southeast Asia in becoming a beneficiary of diffusion."

I think the automotive industry is the best example of what he was talking about. The Japanese companies weren't only buying parts from Thailand. They spent years teaching local suppliers how to meet their production and quality requirements. Those same Thai companies could then go and sell to other customers, using what they'd learned.

BOI is matching new investors with Thai suppliers almost every month

Narit told the audience that when these companies first invest, many of them don't know the suppliers, or who the Thai parts makers are.

That's why BOI has been arranging business-matching meetings almost every month.

Narit said BOI had already held three rounds with BYD and planned to meet Great Wall Motors next month. For SUBCON Thailand 2026, BOI reported more than 9,600 business negotiations and expected sales to exceed THB 23 billion, rather than a total for completed orders. Foreign investors can attend these meetings without changing any of their existing purchasing arrangements. BOI offers grants for supplier development, but it's up to the investor to take advantage of them. BOI also puts expected annual purchases of Thai materials and parts from this year's approved projects at more than THB 693 billion.

Someone in purchasing and engineering at the manufacturer has to take responsibility for getting the Thai supplier approved.

Narit also spoke about the challenge in finding enough qualified people. We have experienced engineers and technicians in Thailand, but several new plants are in competition for the same talent pool at the same time. He gave the example of an optical module plant in Saraburi with more than 10,000 Thai employees, with plans to double that within a year. Add the PCB plants currently being built, which will need tens of thousands of engineers and technicians next year. We can't prepare that many people in the time available. That's why free movement of labor inside ASEAN continues to come up as a barrier to doing business. The second panelist, Jeep Kline of Raisewell Ventures, added that the foreign direct investment (FDI) Thailand should want is the kind "that comes with IP, must also come with the training associated with it". She was speaking specifically for mid-level engineers.

The Thai supplier carries all the risk before the first order

The Bank of Thailand (BoT) Governor Vitai Ratanakorn was blunt in his remarks. He said, "big businesses are very profitable, while SMEs still struggle because they can't plug into supply chains". SME lending is still contracting, which is why he has made growth in SME lending a KPI for everyone at the central bank next year.

Kattiya Indaravijaya, CEO of KASIKORNBANK, explained the banks' concern with figures from the BoT. Out of every million baht lent, roughly 12,000 baht goes bad for large companies. For SMEs, that figure is 99,000 baht. SMEs comprise 99.5% of Thai firms and provide 69% of the jobs, but her slide showed they are only producing 35% of GDP, against 61% in Indonesia and 45% in Vietnam. She has called on the large companies at the top of supply chains to share their know-how with smaller suppliers, keep trade terms fair and link up supply chain data.

Bar chart of SMEs' share of GDP: Indonesia 61%, Japan 54%, Vietnam 45%, Malaysia 40%, Thailand 35%.

Take a Thai Tier-2 supplier trying to get work from one of the new PCB or module plants. A typical ramp-up will include equipment purchase, hiring and training staff, and production trials to complete. In today's set-up, even after passing the customer's qualification process, there's still no guarantee of receiving an order. From the bank's perspective this carries a high degree of risk, with potentially insufficient collateral to support a loan. The supplier bears 100% of the risk and will have to finance much of the preparation itself. Following the commencement of production, there's still the cost of materials, wages and operating expenses which also need to be covered, long before the customer pays the first invoice.

Even after passing the customer's qualification process, there's still no guarantee of receiving an order.

Who commits to buying?

Before the Thai company can qualify, it needs money for the equipment and staff. The manufacturer has already discussed the part, the likely volume and what qualification will involve. The Thai company is going to the bank before an order has been placed. An expression of interest from the customer leaves it borrowing without committed sales.

The Petrobras Progredir program in Brazil allows suppliers to apply for financing against signed contracts, before they deliver the work. In Vietnam, Samsung and the government have helped domestic companies with the production skills and qualifications needed to supply Samsung. I'm not suggesting either program is the same as the arrangement I have in mind. In both cases, though, the large buyer is involved in helping the smaller company get ready to do the work.

Here in Thailand, SMEs Credit Boost from the Bank of Thailand covers part of the credit risk for eligible new lending. It includes loans to larger businesses when the money goes towards supporting SMEs in their supply chains. BOI's agreement with EXIM Thailand, signed in 2024, also deals with financing for investment supply chains. I haven't found the buyer signing for purchases in the published arrangements as part of the Thai supplier borrowing before production.

With BOI bringing them together, the manufacturer, Thai supplier, bank and government credit-guarantee agency could sign one agreement. The supplier would know what the buyer has committed to purchase, including the price, before spending on the preparation. Quality and delivery requirements still apply. Getting the company qualified and training its staff would involve the manufacturer too. After that investment, cancelling without cause would leave the buyer with an agreed amount to pay.

The purchase commitment is then there for the bank to assess. The loan could fund equipment, staff and trials in stages, with a public guarantee for part of the credit risk. The supplier still needs to qualify and supply the parts as specified. Failing qualification doesn't require the manufacturer to buy the parts or pay for cancelling without cause. The preparation costs and loan in that situation would be dealt with on terms settled before the supplier spends. The manufacturer carries some risk in creating a Thai supplier, without being made responsible for the supplier's failure to meet the requirements.

What I did when setting up plants here

Wherever cost was competitive and the quality was there we purchased locally. It's the same with headcount; a local workforce will always be easier to manage, especially from a cultural and language standpoint.

In a previous role I set up a US$20 million manufacturing plant in Thailand in nine months, starting from an empty rented building. When we first opened the new facility, we manned the production floor with technical teams already familiar with the customers' products working in another building. Only after having filled that capacity did we begin looking outside for additional manpower.

Where the skills are in short supply or don't yet exist in Thailand, you bring in experienced people from overseas.

PCB manufacturing is a good example.

Existing PCB plants are already competing for the same limited number of experienced engineers and technicians, and there are more factories under construction today.

The semiconductor industry isn't much different. Thailand has one established Thai chip-design company, along with several companies doing chip assembly, packaging and testing. The balance of them are mostly foreign-owned. Where we are lacking is enough Thai engineers with experience in some of the newer technologies coming into the country, and fresh graduates entering the workforce today who are not ready to step into those roles with 100% independence. There is significant on-the-job training which needs to take place first and can take years to develop.

The Bangkok Skytrain project (BTS) is worth remembering here. The first BTS lines were built back in the 1990s with the help of specialists who had worked on rail projects overseas. Thai engineers and technicians were on the project with them and gained that experience firsthand. Much of the operation and maintenance has since been taken over by Thai staff. Manufacturing shouldn't be any different, and if tied to the incentives as part of the sustainability plan, it will be successful long-term. This is now one of the new requirements for companies applying to build data centers here.

How should a manufacturer building in Thailand plan its local suppliers?

If you're deciding to build in Thailand, start developing a plan for the local supply base at the same time as the site. Ask BOI for business matching while construction is ongoing. In many cases in a new facility, customer and site qualifications will take the same amount of time as using existing suppliers. The long-term benefit will not only be on cost, but if the product source of origin mix is challenged for export, this may help, depending on the product and the destination market's origin rules, and in situations where the minimum mix can be increased, BOI provides additional benefits under its local-content measure for specified EV, electrical-appliance and electronics activities, subject to its local-content and certification conditions. For components or services that cannot immediately provide the solutions, a local supply chain development plan should be put in front of BOI for support as early as possible.

BOI applications reached THB 1.71 trillion in the first nine months of 2026

BOI's figures for the first nine months of 2026 show applications have reached THB 1.71 trillion from 1,954 projects, which is a 28% increase over the same period last year. Promotion certificate issuance (the stage BOI calls closest to actual investment), tallied THB 1.05 trillion from 1,961 projects, which is also up 10% on last year. Narit said candidly that he feels the application total is still too little. He believes that with Thailand's footprint and resources we should be able to do a lot more. BOI approved the TikTok System (Thailand) expansion on May 6th at THB 842.35 billion.

Bar chart, BOI January to September 2026: applications THB 1,707 billion, approvals THB 1,513 billion, promotion certificates THB 1,048 billion, expected purchases of Thai materials and parts THB 693 billion a year; purchases from Thai-owned suppliers not published.

Purchasing figures would show what reaches Thai-owned suppliers

Before a factory produces anything, it may already have spent a lot on the land, building and machinery brought in from overseas. Purchasing figures from the manufacturers getting BOI promotion could show how much work is reaching Thai-owned companies once production starts.

There is no need to publish the supplier's individual prices or contracts. The number of Thai-owned companies that qualified, the amount bought from them and the orders continuing into the next year would give BOI something to assess the supplier-development incentives against. The purchasing and engineering departments would then have work to finish after the matching meeting, getting the supplier approved and placing orders.

Nakarin Wanakijpaibul, THE STANDARD reaches the Thai SME owners who are the ones that need to step up. From your discussions with them, what do they tell you is preventing them from doing so?

Which Thai suppliers a foreign manufacturer can qualify, and in what sequence, is part of the second source work of HundredEast, the independent advisory firm Marc Spiegel founded in Bangkok.